Anyone Know of Rubber Protector Feet for MA2?

[Piper J3]

Does anyone make slip-on rubber feet to protect plastic landing pads - front, back, and bottom for the MA2?

 

[WildcatDave]

not exactly rubber feet but this is an alternative component. looks like it's easily added and removed...

Portable New Disassemble Anti-fall Anti-dirt Landing Gear Protection Rack for DJI Mavic Air 2 | Wish

Buy Portable New Disassemble Anti-fall Anti-dirt Landing Gear Protection Rack for DJI Mavic Air 2 at Wish - Shopping Made Fun

www.wish.com

 

[WildcatDave]

or these...

Mavic Air 2 Landing Gear 3D Printed 5cm Heighten Landing Legs Extended Support Feet for DJI Mavic Air 2 RTF Drone Accessories | Wish

Buy Mavic Air 2 Landing Gear 3D Printed 5cm Heighten Landing Legs Extended Support Feet for DJI Mavic Air 2 RTF Drone Accessories at Wish - Shopping Made Fun

www.wish.com

 

[JayTea26]

See PGYTECH. I GOT MY LANDING GEAR THERE.

 

[WildcatDave]

See PGYTECH. I GOT MY LANDING GEAR THERE.

are you using their tablet holder as well. I'm curious to see how much strain that puts on the controller if you use a 10-in tablet.

 

[portermann]

you could try these

This item is unavailable - Etsy

Find the perfect handmade gift, vintage & on-trend clothes, unique jewelry, and more… lots more.

www.etsy.com

 

[Ron (MM)]

Amazon MA2 accessories.

 

[mschaffer66]

are you using their tablet holder as well. I'm curious to see how much strain that puts on the controller if you use a 10-in tablet.

I had one and no longer use it. Long term it seemed like a lot of leverage on those tubes.

 

[Ron (MM)]

I use a 10'' Tab S4. No problems and no strain on antenna support.

 

[Piper J3]

I found 3/8" rubber thread protectors on eBay for $5 free shipping.

I put a thin foam tape on the bottom rear skids.

 

[Airmaxx23]

I drew these up yesterday and print them in TPU. I can post them to Thingiverse if someone wants to print them. I also drew up protectors for the rear skids, I'll test print them once I'm done printing a tablet mount for someone.

 

[Piper J3]

What is orange tape? Is that to remind you to remove gimbal cover?

 

[Airmaxx23]

What is orange tape? Is that to remind you to remove gimbal cover?

Yes, it's a piece of duct tape.

 

[Airmaxx23]

Here's the protectors for the back feet that I drew up and printed in TPU.

 

[Droning on and on...]

What exactly are you guys trying to prevent? After several hundred flights off of asphalt and concrete, looking at the bottom of my drone, I can assure you that all of the moving parts will wear out long before the landing gear.

Seems like a solution in search of a problem that does nothing more than weigh down your drone.

Just my opinion.

 

[Airmaxx23]

What exactly are you guys trying to prevent? After several hundred flights off of asphalt and concrete, looking at the bottom of my drone, I can assure you that all of the moving parts will wear out long before the landing gear.

Seems like a solution in search of a problem that does nothing more than weigh down your drone.

Just my opinion.

I'm doing it just as a preventative measure, the 4 - 3D printed feet weigh less than 3 grams total so weight isn't an issue.

 

[Droning on and on...]

I'm doing it just as a preventative measure, the 4 - 3D printed feet weigh less than 3 grams total so weight isn't an issue.

Preventative measure to prevent what? The landing gear will never show significant signs of wear over the lifetime of the drone.

 

[Airmaxx23]

Preventative measure to prevent what? The landing gear will never show significant signs of wear over the lifetime of the drone.

My case has stained the front feet black and I just like the idea of landing on a softer material rather than the hard plastic. I don't want any signs of wear at all.

 

[Droning on and on...]

My case has stained the front feet black and I just like the idea of landing on a softer material rather than the hard plastic. I don't want any signs of wear at all.

Fair enough.

 

[cheukhin.tse]

@Airmaxx23 Please post it on Thingiverse, I would love to print this awesome design out.

Here's the protectors for the back feet that I drew up and printed in TPU.