DJI Mavic, Air and Mini Drones
Friendly, Helpful & Knowledgeable Community
Join Us Now

Recent content by Damien66

  1. Damien66

    Czech Republic - Mavic pilots

    Dej vědět, jestli to update vyřešil ;-)
  2. Damien66

    Czech Republic - Mavic pilots

    Ahoj! A jsi z Prahy? Zkušenosti jsou cenná informace, to rozhodně, školení doporučuji a nebo se můžeme nějako sejít (a klidně ve více lidech) a já ti dám instruktáž :-D Pojištění řeším, ale stále narážím na takovou drobnost a sice, že dle ÚCL můžeš létat jen tam, kde se nic nestane (když to...
  3. Damien66

    NFZ Limit Cannot Take Off After .600 Firmware

    Hello, I am joining this party too. I think that everybody who upgraded to .600 have this issue. Symptoms are completely the same as described here in "focus" reply. Hope DJI will fix it soon. Regards!
  4. Damien66

    Mavic Pro Build Info - Serial Number?

    Last question at all - do you think that it is a good idea to crack my bird just to see twisted or untwisted wires? I have no issues while flying in sports mode, compass bars are green when flying at full forward and up (100% power). I if crack it, I do it just for knowleadge of this thread ;-)
  5. Damien66

    Mavic Pro Build Info - Serial Number?

    Hello, so definitely the date of trashcan and Anatel logo switch is 29th Nov. I have seen some pics here, where 30th Nov had Anatel logo, my bird was made 29th Nov and I have trashcan.
  6. Damien66

    Czech Republic - Mavic pilots

    Karlštejn - SUPER! Opravdu velmi velmi fotogenická stavba, to jsem ani nečekal ;-) O tom Obstacle Avoidance proti slunci vím, mám to v Pre-flight checklistu co jsem si sestavoval, je potřeba promyslet, jestli poletíš proti slunci. Hlavně bacha na to, že při RTH by ti protislunce mohlo zcela...
  7. Damien66

    Mavic signal lost when POI or other modes

    I understand, that in POI, it continues circling, so there is big chance to gain control back, but it should RTH at RTH battery level. I will test it deeply this weekend and let you know. And for sure, I will test all the modes. The only reason I started this thread is, that I want to POI...
  8. Damien66

    Czech Republic - Mavic pilots

    Ahoj Vašku! Parádní fotka! Zalítal sis pořádně? Já v sobotu létal na letišti, vyzkoušel jsem maximálku 500m a i letěl zatím nejdál - 2900m od home pozice, signál 3 až 4 sloupky z 5. Jo a taky jsem zjistil, že Mavic v režimu Waypoint a POI nespustí RTH po ztrátě signálu!
  9. Damien66

    Mavic signal lost when POI or other modes

    Perfect question! I think, it goes to that 10% level (if not changed by user) and start to descent.
  10. Damien66

    Mavic signal lost when POI or other modes

    Thank you for your reply! So should I use these two functions with caution, that if I am too far and lost signal, Mavic could land somewhere, where I could not find it (the worst situation of course). Regards!
  11. Damien66

    Mavic signal lost when POI or other modes

    Hello pilots! Technically, this should be duplicate thread, but I could not find any reliable answer. Today I tried POI starting with 100% battery, 100m far from me, open area, 30m diameter, 40m high. During POI mode, I switched my RC off, but no RTH happened, bird continued circling. I left...
  12. Damien66

    Gimbal problem

    I found it inside my share gallery! So here it is, make inspection, may be that you have the same problem ;-) Photos on the top - before fix Photos on the bottom - after fix Sent from my iPad using MavicPilots
  13. Damien66

    Gimbal problem

    Hello, a had a very simillar problem. Try switching portrait mode and back on the ground and look at gimbal, if it turns smoothely. Finally I found, that my problem was in small black cover under objective. It was not in place and touched rotating movements, so friction was too high to allow...
  14. Damien66

    Czech Republic - Mavic pilots

    Kupoval jsem je přímo tady: DJI Mavic Filters - Cinema Series 6-Pack Ale opravdu mají asi dovolenou :-/
  15. Damien66

    Problems connecting to DJI assistant 2

    Hello! RNDIS is "Remote Network Driver Interface Specification", Mavic talks with PC via "Virtual Ethernet Adapter" (something like network card, just propietary). But you need to solve your issue, I suppose. Please, try to disable Windows Firewall completely, then start DJI Assistant 2 app...