In the past, I've flashed my MPP to 1.03.07 and 1.03.06 and back to 1.04.0100.
Last flash was to 1.03.0700 then to 1.04.000 with 305/306 deleted. However, it crashed in the middle of it.
Now I cannot flash at all. I've tried DMULdore, No Limits Dronez, and factory DJI assistant. Nothing will complete past 15%. All software that can read the FW says 1.03.0700. I can mod the settings for things like height and changed the decent rate. However, I get a motor current error (doesn't say overload), and I cannot use active track. When I land and when auto landing, it doesn't slow down, it lands pretty hard.
Here is what I've tried, many times.
Using DJI assistant 2 v1.2.0 only:
Assistant v.1.2.0 Trying to upgrade to 1.04.000 from mixed module of 1.03.0700 to 1.04.0000. According to NLD Mod Client it says my FW is 1.03.0700. Closed NLD Mod client (only used to verify FW).
Start assistant and shows Mavic is connected, also going to internet, IP ftp://192.168.42.2/ shows my 4 files listed: blackbox, flyctrl, upgrade, v2.
Assistant2: Downloading v1.04.0000 : 100%. Red solid front LED, Flashing Yellow rear.
Transmitting : 100%. Red solid front LED, Flashing Yellow rear.
Updating : 15% Update Failed (after 15 seconds). Red flashing front LED, Flashing Yellow rear. Front red LED turns off.
Upload Error Log. Red line says: undefined 0x032800. Restart the DJI device before updating the Firmware. Yellow rear light remains flashing throughout the process.
Retry selected 5-8 times over two days.
Lands too fast. If I hold down throttle, it will land at water speed I have it at. When using auto land, it very firmly lands.
Latest DUMLdore 2.14.0.0
Red LED solid, rear yellow flashing.
Assistant v.1.2.0 shows connected and FW version.
Turned off/exited Assistant 1.2.0
Started DUMLdore 2.14 .
Selected backup: Timed out attempting to contact the FTP server on the device.
You can test for connectivity by going to ftp:192.168.42.2 with a browser. If you cannot access via the IP address, check your RDNIS driver.
DUMLdore says on the bottom: FTP access failed.
I can, and always have been able to, get to 192.168.42.2. I can see and access and brows the files there.
Blackbox, flyctrl, upgrade,v2.
I can close the dialogue box from the error trying to backup and select load FW.
I select load firmware 1.04.0000 downloaded. (I’ve tried other FW also with same results).
I select flash: The firmware file will be sent to the device. Make sure you have at least 50% battery remaining. This will take up to 30 seconds. Press OK and wait for the confirmation dialog. I select OK. Mavic flashes red one time, and yellow remains flashing.
I close DUMLdore.
After a couple seconds the Front LED changes from Solid red to flashing. However, after a about 10 seconds, it goes out and stays out. Rear flashing yellow is still flashing yellow.
Not ever happens after this. I have to restart the mavic to get the front LED to come back on solid. However, even while LED is out on the front legs, I can still access the FTP address. And, if I restart assistant, It can still connect to the Mavic.
I can let this sit till the battery is dead. Nothing happens.
Next flashing effort suing NLD Mod client from No limits dronez. It requires assistant 1.1.2 so I uninstall assistant 1.2.0 and install 1.1.2 from their website.
Install NLD DJI assistant 1.1.2. Start Assistant.
Restart Mavic, red led is on, yellow rear flashing.
Start NLD app, says Mavic FW is 1.03.0700.
Select firmware manager, select upgrade: 1.03.100 which is the highest available option on NLD MOD.
Downloading FW. 100%. Flashing yellow rear, solid red front.
Downloading dependency: 100%
Uploading firmware: 100%. Front LED red and solid.
Flashing firmware progress bar, please wait, 7% 10:04, 15% at 12:04. 100% 12:04 immediately after 15%.
Uploading firmware phase 2. 100%.
Flashing firmware: 7% 12:04. 15% 12:05. 3 seconds later, 100%.
Flashing phase 3. Red LED solid. Uploading FW 100%
Flashing: red led flashing through 7%, then 15%, then immediately to 100%, LED goes solid.
Nothing happens, the process just stops.
I cannot get past 15%.
Any suggestions?
Last flash was to 1.03.0700 then to 1.04.000 with 305/306 deleted. However, it crashed in the middle of it.
Now I cannot flash at all. I've tried DMULdore, No Limits Dronez, and factory DJI assistant. Nothing will complete past 15%. All software that can read the FW says 1.03.0700. I can mod the settings for things like height and changed the decent rate. However, I get a motor current error (doesn't say overload), and I cannot use active track. When I land and when auto landing, it doesn't slow down, it lands pretty hard.
Here is what I've tried, many times.
Using DJI assistant 2 v1.2.0 only:
Assistant v.1.2.0 Trying to upgrade to 1.04.000 from mixed module of 1.03.0700 to 1.04.0000. According to NLD Mod Client it says my FW is 1.03.0700. Closed NLD Mod client (only used to verify FW).
Start assistant and shows Mavic is connected, also going to internet, IP ftp://192.168.42.2/ shows my 4 files listed: blackbox, flyctrl, upgrade, v2.
Assistant2: Downloading v1.04.0000 : 100%. Red solid front LED, Flashing Yellow rear.
Transmitting : 100%. Red solid front LED, Flashing Yellow rear.
Updating : 15% Update Failed (after 15 seconds). Red flashing front LED, Flashing Yellow rear. Front red LED turns off.
Upload Error Log. Red line says: undefined 0x032800. Restart the DJI device before updating the Firmware. Yellow rear light remains flashing throughout the process.
Retry selected 5-8 times over two days.
Lands too fast. If I hold down throttle, it will land at water speed I have it at. When using auto land, it very firmly lands.
Latest DUMLdore 2.14.0.0
Red LED solid, rear yellow flashing.
Assistant v.1.2.0 shows connected and FW version.
Turned off/exited Assistant 1.2.0
Started DUMLdore 2.14 .
Selected backup: Timed out attempting to contact the FTP server on the device.
You can test for connectivity by going to ftp:192.168.42.2 with a browser. If you cannot access via the IP address, check your RDNIS driver.
DUMLdore says on the bottom: FTP access failed.
I can, and always have been able to, get to 192.168.42.2. I can see and access and brows the files there.
Blackbox, flyctrl, upgrade,v2.
I can close the dialogue box from the error trying to backup and select load FW.
I select load firmware 1.04.0000 downloaded. (I’ve tried other FW also with same results).
I select flash: The firmware file will be sent to the device. Make sure you have at least 50% battery remaining. This will take up to 30 seconds. Press OK and wait for the confirmation dialog. I select OK. Mavic flashes red one time, and yellow remains flashing.
I close DUMLdore.
After a couple seconds the Front LED changes from Solid red to flashing. However, after a about 10 seconds, it goes out and stays out. Rear flashing yellow is still flashing yellow.
Not ever happens after this. I have to restart the mavic to get the front LED to come back on solid. However, even while LED is out on the front legs, I can still access the FTP address. And, if I restart assistant, It can still connect to the Mavic.
I can let this sit till the battery is dead. Nothing happens.
Next flashing effort suing NLD Mod client from No limits dronez. It requires assistant 1.1.2 so I uninstall assistant 1.2.0 and install 1.1.2 from their website.
Install NLD DJI assistant 1.1.2. Start Assistant.
Restart Mavic, red led is on, yellow rear flashing.
Start NLD app, says Mavic FW is 1.03.0700.
Select firmware manager, select upgrade: 1.03.100 which is the highest available option on NLD MOD.
Downloading FW. 100%. Flashing yellow rear, solid red front.
Downloading dependency: 100%
Uploading firmware: 100%. Front LED red and solid.
Flashing firmware progress bar, please wait, 7% 10:04, 15% at 12:04. 100% 12:04 immediately after 15%.
Uploading firmware phase 2. 100%.
Flashing firmware: 7% 12:04. 15% 12:05. 3 seconds later, 100%.
Flashing phase 3. Red LED solid. Uploading FW 100%
Flashing: red led flashing through 7%, then 15%, then immediately to 100%, LED goes solid.
Nothing happens, the process just stops.
I cannot get past 15%.
Any suggestions?
Last edited: