DJI Mavic, Air and Mini Drones
Friendly, Helpful & Knowledgeable Community
Join Us Now

Recent content by ziv2liv

  1. Z

    HOA demands that I stop flying drones in the neighborhood. Need advice

    Yes, here is an advice, stop flying in your neighborhood... On the other hand, check the bylaws. If there is no mention of launching an aircraft of any kind from the HOA controlled grounds, they have no base for their request, other than appealing to the goodness of your heart. They control the...
  2. Z

    Lost my Mavic 3 today while recording alligators - video

    Quite possibly your IMU went out of calibration. Check this link out. https://www.dronenerds.com/videos/mavic-tutorials--imu-calibration.html#:~:text=Calibrating%20the%20IMU%2C%20turn%20on,IMU%20and%20tap%20calibrate%20IMU.
  3. Z

    Mini 3 pro not as good as expected?

    I watched the video you linked in, and I'm not sure if the comparison is fair. Unless those videos were shot on different days at exact time, this cannot be a fair comparison. Shooting in "Magic hour" is tricky. The light changes fast so if you shot one drone after another, it is quite...
  4. Z

    Mini 3 pro not as good as expected?

    My big issue with the M3P is auto-focus, and I think it's not the camera but rather the gimbal. I shot several frames at 48mp that look fine until you enlarge the photo (Zoom in), than you notice fuzziness. The reason I suspect it's the gimbal is because when the drone is grounded, the photo...
  5. Z

    Serial Number of my Mavic 2 Pro changed after service

    Thank you so much. That makes a lot of sense.
  6. Z

    Serial Number of my Mavic 2 Pro changed after service

    Hello everyone, After receiving error code 200 which rendered the aircraft unusable, I sent it to DJI for a check and their prognosis was that the gimbal received no power at all. Hmmm... kinda strange cause the drone never crashed or hit anything, but okay. After the repair was done, they...
  7. Z

    error 200

    I had the same error, sent the drone to DJI for repair. They claimed that the gimble did not have any power and that is the reason. The drone never crashed or damage which raises my eye brow. Repair cost around $200
  8. Z

    Battery status N/A on Mavic 2 Pro

    Today I heard from DJI again, They rendered the battery "Damage" which in my book is "malfunctioned" cause there was no damage to the battery. Since it's already happen twice, I will stop using the multi charger, and use DJI direct connection only. They did offer me another...
  9. Z

    Battery status N/A on Mavic 2 Pro

    No, and it doesn't seem it will be resolved anytime soon. As I'm typing, my drone is at the DJI repair center, for a repeating error (Code 200) as well as for the battery issue, however dealing with DJI has been a nightmare. I sent them the drone about three weeks ago, and after acknowledging...
  10. Z

    Battery status N/A on Mavic 2 Pro

    No. I contacted DJI and they didn't have an off hand answer, they suggest to send the drone with the faulty batter to them to check it, but I'll be going out of the country in the beginning of June and I will need the drone. I may take on their offer when I come back. I used the power bank...
  11. Z

    Battery status N/A on Mavic 2 Pro

    Thank you for the response, It happened two me twice already. Two different cameras, two different sellers. I was just wondering if there is solution to reset them or any other way to fix them. Thanks
  12. Z

    Battery status N/A on Mavic 2 Pro

    Hello everyone. This problem has occurred to me with two different batteries already. A fully charge battery inserted into the drone and the controller show battery status as N/A. Upon attempting to take off, I get a warning telling me that there is only enough "juice" to fly home. Is there any...