Mavic 4 Pro - Obstacle Avoidance Issues
- Thread starter fgphoto
- Start date
It seems a production batch version had these issues. Glad to hear yours was resolved.
Well, there goes the theory that it is only the 64 GB versions. So far then, it seems like the Canadian DJI sourced ones are immune, such as the Adorama units in the U.S. and those bought in Canada.
Since I see you are in California, did you purchase from the DJI Canada web site and have it delivered to a Canadian address?
BlairAir
Well-Known Member
This is the DJI ND Filter - I have a 512GB Creator Combo Aircraft, date not handy (box in the attic, but I will check and update this post) The filters from DJI have nothing special where the Pogo Pins for the E-ND Filter are. They justhave tabs for the non-powered Sping pis on the camera Module. I Updated to V01.00.0200 Before ever flying it, and have experience no issues other than the typical twitchiness when it's taking off around some obstacles. Once it's clear,I have none of the falsing behavior reported here.
Last edited:
Well, then maybe just the Creator Combos from DJI Canada are immune. The field of immunity keeps narrowing!
Frontier
New Member
I have the same issue with my Mavic 4 Pro Creator Combo. The drone was manufactured on 04/2025 and was bought from the DJI EU store. Currently I have an open case with the support and sent over 5GB of log data to them.
Do you remember what date your first M4P was manufactured and what is the date of manufacturing of the replacement?
I will ask them to replace the drone but I do not want to use my care refresh as it is not my fault for not working properly.
Thank you very much in advance.
Frontier
New Member
An update to my case, in case it might be helpful to anyone.
After contacting dji support, they suggested to send the unit back to them for inspection.
Before doing so, I thought to try one more time to self-calibrate the sensors.
DJI support suggested that I should perform a low-flight altitude on an area with obstacles and particular something above the aircraft, flying the aircraft on four directions for 2-3 minutes. This did not help at all as it kept detecting false obstacles.
What DID help and fixed the issue was this:
I went to an open area without obstacles (an empty football field) and performed a low altitude flight (2-3m over the ground), flying the Mavic 4 Pro in a cross-like pattern front/back/left/right with obstacle avoidance set to off (not bypass nor brake). The flight was less than 5 minutes (3-4 minutes) and after performing the cross-like flight pattern, I've landed and powered off the aircraft.
This was done 3 times in sequence.
After that, the sensors no longer detect false obstacles, the drone flights fine with either bypass or brake obstacle avoidance action and I can perform automated flights (Mastershots, Waypoints, etc) without issues on the same areas that previously was not possible (in these same areas, the Mavic 3 can do them without issues).
In any case, that's what I did and now the aircraft is working perfectly.
Hope this helps someone.
After contacting dji support, they suggested to send the unit back to them for inspection.
Before doing so, I thought to try one more time to self-calibrate the sensors.
DJI support suggested that I should perform a low-flight altitude on an area with obstacles and particular something above the aircraft, flying the aircraft on four directions for 2-3 minutes. This did not help at all as it kept detecting false obstacles.
What DID help and fixed the issue was this:
I went to an open area without obstacles (an empty football field) and performed a low altitude flight (2-3m over the ground), flying the Mavic 4 Pro in a cross-like pattern front/back/left/right with obstacle avoidance set to off (not bypass nor brake). The flight was less than 5 minutes (3-4 minutes) and after performing the cross-like flight pattern, I've landed and powered off the aircraft.
This was done 3 times in sequence.
After that, the sensors no longer detect false obstacles, the drone flights fine with either bypass or brake obstacle avoidance action and I can perform automated flights (Mastershots, Waypoints, etc) without issues on the same areas that previously was not possible (in these same areas, the Mavic 3 can do them without issues).
In any case, that's what I did and now the aircraft is working perfectly.
Hope this helps someone.
This worked for me!
I have had Mini 4 Pro and Mavic 3 Pro and never had these issues of false obstacles detections, as I was getting frustrated with this problem with my Mavic 4 Pro (non creator combo).
I bought it yesterday, experienced the problem, came to this forum and updated the firmware using DJI Assistant 2. (I have it already on 0200, but the software allowed me to install new firmware)
Today, I am happily writing right after repeating Frontier’s procedure on a soccer field, with some trees at the boundaries, flying at 4 meters high and doing 4 repetitions of his patterns. It worked like a charm! Now it is flying OK with OA on.
Apparently the drone learns by itself, and I think that flying carefully in N mode and with OA set to off helps to feed its OA algorithm.
Thanks again Frontier and all the people who have shared their experience on this forum!
I had the same issue on the first two flights. I then flew random patterns at about 15' for ten minutes and the problem resolved. I don't think there's anything significant about the flight path or speed; the drone just needs a little flight time at low altitude to calibrate itself.
Last edited:
So:
In N mode, with anti-obstacle sensors active, and brake on off.
Interesting.
What speed did you keep? Thank you
Similar threads
DJI Drone Deals
New Threads
-
-
-
-
-
My device is the RM500, and it has an issue where it won't turn on.
- Started by apeng
- Replies: 0
Forum statistics
