Mavic Mini Prop Holders and Protectors

[TruGreen]

I found these on the good ole' Ebay. Shipping from Hong Kong took a few weeks. Must say I'm impressed though. They are 3D printed, but fully cover the motors and props. Perfect for pocket carry so they blades don't snag. Mini does fit inside the Fly More case, but it a tad snug. So when removing the Mini the holder stays in the bottom of the case, which isn't really a bad thing. Over all I'm happy with these and they deff will protect the blades better then them flopping around.

 

[Badgerman26]

These ones?

 

[scooot]

These ones?

That’s the ones.I ordered some after Trugreen first posted about them.I haven’t received mine yet so I can’t comment but they look
good from what I have seen.

 

[GerdS]

I designed and use these. Fits perfectly with the Fly More case.

 

[TruGreen]

These ones?

yes those are the same

 

[TruGreen]

I designed and use these. Fits perfectly with the Fly More case.

am i missing the pic? or did you not post one?

 

[deepakvrao]

Those look great. They dont ship to India, and I cant seem to find them elsewhere. I'm sure they will come up on Aliexpress sometime.

 

[Lifeisfun]

These look ok as well
prop covers

 

[GerdS]

am i missing the pic? or did you not post one?

Just follow my link behind "these".

 

[TruGreen]

These look ok as well
prop covers

yea saw those too but wasnt digging the silicone and the fact they are more open. granted yes they hold the blades. but if wanted to carry in a hoody/jacket pocket you may get lint or pocket stuff inside the motors since they are exposed and not fully covered.

 

[TruGreen]

Just follow my link behind "these".

gotcha i missed the link prior to my comment

 

[amadeo]

i use this one..

 

[TruGreen]

i use this one..View attachment 88020

do you have the fly more case? cause with the bottom props like that i dont think it will properly fit the case and if it does fit. it may be unwanted stress and pressure on the blades.

 

[amadeo]

do you have the fly more case? cause with the bottom props like that i dont think it will properly fit the case and if it does fit. it may be unwanted stress and pressure on the blades.

fits perfectly inside the fmc case. no stress at all.

 

[TruGreen]

fits perfectly inside the fmc case. no stress at all.

thats good i just worry cause the case shows the bladed should be like the holders i have since they sit lower and the case is formed that way

 

[MMMark]

Thanks for the tip! I like the closed ones as well - to protect against pocket lint etc.

Tru Green - where’d you get the profile shark face? Way cool!

Thanks,
Mark

 

[TruGreen]

Thanks for the tip! I like the closed ones as well - to protect against pocket lint etc.

Tru Green - where’d you get the profile shark face? Way cool!

Thanks,
Mark

shark decal

Flying Tigers Shark Teeth Vinyl Decal Stickers v2 P-40 Warhawk 1 Pair - 2" in. | eBay

Flying Tigers Shark Teeth Vinyl Decal Stickers. Quantity: 2 Vinyl Decal Stickers. Digitally printed using Eco-Solvent CMYK ink on premium Oracal vinyl material. Laminated to protect against scratches.

www.ebay.com

stock is red. but i had messaged to see about changing the color and they said was fine just leave a note with the desired color. i did also need a trim a bit off the front. i left the gimbal cover installed while i placed the decal then just traced and cut to remove the extra stuck to the cover

 

[MaxE1955!]

These ones?

eBay description reads "Doesn't ship to United States"

 

[TruGreen]

eBay description reads "Doesn't ship to United States"

hes in the UK and thats a UK Ebay link

 

[MMMark]

That's awesome! Thanks for sharing. I'll order a set once the seller is back. When I saw your original post I thought the decal was just on the arm of the Mini. Cool to see the whole thing! Also going to order a set of the prop holders.

Thanks again,
Mark