I've refreshed everything. I'm grounded. Not starting a support ticket because I think this latest version of Assistant 2 (Consumer) is the culprit. Time will tell!
Anyone Bitten with the "30064" Error?
- Thread starter KLRSKIR
- Start date
I'm new to the game, but am stuck with the 30064 error on my Mini Pro 3 as well.
Very disappointing.
One thing I noticed was the user manual error light indicators, that the drone lights are blinking Red (slow to me) indicating a low battery even though the battery is reporting on the controller that it's 88%. So did the last update screw up the "Intelligent Battery"?
Very disappointing.
One thing I noticed was the user manual error light indicators, that the drone lights are blinking Red (slow to me) indicating a low battery even though the battery is reporting on the controller that it's 88%. So did the last update screw up the "Intelligent Battery"?
Last edited:
I had flown a few days prior to my lock out, and then connected the drone and made sure each battery was refreshed and up to date (Fly More pack batteries) since I had been on vacation the week earlier.
Then a couple days later on the 29th fired it up to show a co-worker in town and can't lift off.
Then a couple days later on the 29th fired it up to show a co-worker in town and can't lift off.
For me it started September 1st. Most likely the latest version of Assistant 2 (Consumer) via PC/MAC. It added the Avata and crinkled the Mini 3 Pro.
Check this too from a year ago: 30064 Error @ DJI Forum
Last edited:
Not surprising there was a Mini Pro 3 user who posted on 8/31. I added a comment as well.For me it started September 1st. Most likely the latest version of Assistant 2 (Consumer) via PC/MAC. It added the Avata and crinkled the Mini 3 Pro.
Check this too from a year ago: 30064 Error @ DJI Forum
Also new thread on Mini Pro 3 30064 Error: Unable to take-off (Code: 30064)
Last edited:
The same error 30064 for me after using DJI Assistant 2.1.11. The previous release doesn’t ricognizione Mini 3 pro.
I found this link DJI Mini 3 Pro unable to take off or fly after Assistant 2.1.11 update
I found this link DJI Mini 3 Pro unable to take off or fly after Assistant 2.1.11 update
I'm planning on purchasing my mini 3 pro on a quick trip through the US on my way to Europe - question: I won't have a laptop with me, only my phone - is Assistant 2 necessary for updating the drone and controller firmware, etc? Or can it be done directly?
The DJI Fly app takes care of all updates for the Fly app, Firmware & Fly Save databases (internet required), no need for Assistant-2/computer.
You can use the DJI Fly app and either controller to update. No need for a computer. Must have access to internet via WiFi.
I would go so far as to NEVER use DJI Assistant 2 for your Mini 3 Pro and ALWAYS use the Fly App or RC controller to update. Those of us who unknowingly used Assistant 2 are going through some pain right now as we are grounded until a new FW hits. Everyone else is still flying.
Yeah, that's some sound advice. It's definitely the sort of trap I'm liable to fall into being the kind of person who likes to tinker with everything. Leave well enough alone goddammit!
DashSolo
Well-Known Member
Unless you need to do a sensor calibration. Also, there are some who have been grounded using the Fly app to update, ie., brand new aircraft right out of the box!
I spoke with DJI Susan and she is sending me a link to an "optimized firmware package." I'll post back when that happens.
Sensor calibration is how I got stung.
Interesting. I want to know more about that. Optimized sounds good.
Similar threads
DJI Drone Deals
New Threads
-
-
I think the FAA is missing it with the 107 requirements
- Started by edmartin123
- Replies: 2
-
Go4 not installing from DJI Download Center- Started by conchman
- Replies: 0
-
-
Forum statistics
