Could someone 3D print something similar?

[UrbanPhotoSniper]

I don't have a 3D printer but how hard would it be to 3D print something similar to this that clips around the top of the battery and locks around the battery buttons on the side? Except make the top flat so a tracker could be attached and have it the same color as the Mavic.

 

[BD0G]

What tracker are you planning on using?

 

[UrbanPhotoSniper]

What tracker are you planning on using?

Trackimo, this is what I'm doing now.

 

[Starz]

There are several people over on the rcgroups website that advertise that service. I dealt with harvcopter and was very satisfied.

 

[BD0G]

http://www.gimbal-guard.com/_p/prd13/4597268561/product/trackimo-holder-for-dji-mavic-pro

 

[BD0G]

This could be adapted to fit the Trackimo

Soporte RF-V16 para Mavic Pro. V2 by Desmen

 

[G284L]

This guys has what your looking for.

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

Sent from my iPad using MavicPilots

 

[halley]

I prefer @BD0G / Desmen's design for a cap flattener, over the original battery clip idea on the top post.

The reason GoPro Karma falls out of the sky is because something let the battery get loose. You do NOT want something that could accidentally squeeze on the Mavic battery latch buttons while in flight.

 

[CactusJackSlade]

This could be adapted to fit the Trackimo

Soporte RF-V16 para Mavic Pro. V2 by Desmen

Isn't that spot right on top of the Mavic's GPS?

 

[halley]

Isn't that spot right on top of the Mavic's GPS?

GPS antennae are near the white DJI logo over the back end of the main body. The tail cable at 6m:00s in this video is where it connects.

 

[dmyers7]

Yes, but that is right where 1 of 2 compasses are. The other being in the backend.


Sent from my iPad using MavicPilots

 

[mike venziano]

i seen ping a new gps tracker smaller than tile any ideas about it

 

[UrbanPhotoSniper]

i seen ping a new gps tracker smaller than tile any ideas about it

I looked into ping but it's too early to tell. It doesn't track, it will only tell location if you click update in the app. So if your Mavic goes down and for some reason you can update it you'll never know. At least with trackimo it tracks it on the map.

 

[BD0G]

Marco Polo trumps those GPS based trackers if flying in areas with no cell phone signal. I fly in lots of areas like that and realize it is bad to loose the Mavic Pro and even worse to loose it with a cell signal based tracker strapped aboard.

Fly with what you like and let me post my "I told you so" early

 

[CactusJackSlade]

GPS antennae are near the white DJI logo over the back end of the main body. The tail cable at 6m:00s in this video is where it connects.

Oh yeah, I see it now,,, you can see what is probably the GPS unit on the underside of the shell when he pulls it off.

 

[BrunoBronosky]

GPS antennae are near the white DJI logo over the back end of the main body. The tail cable at 6m:00s in this video is where it connects.

What makes you sure that's where the GPS antenna is? At 01:55 I see the 4 pigtails (which he calls "all these wifi connections" #sigh) but I can't figure out where any antennae are. I can find nothing that looks like the classic tan square GPS antenna. gps antenna adafruit - Google Search

 

[mstevens]

I don't have a 3D printer but how hard would it be to 3D print something similar to this that clips around the top of the battery and locks around the battery buttons on the side? Except make the top flat so a tracker could be attached

If that piece itself is 3D printed and the file can be obtained, altering the design should trivially easy. In that case the answer would be "not very hard".

If there isn't an existing design file, then it becomes more difficult. Someone is going to have to scan the Mavic, do some designing, do some test prints, etc.

The actual printing isn't necessarily the hard part.

and have it the same color as the Mavic.

The color of the final product depends on the color of the filament used. If you can find filament in a matching color, then this would be extremely easy. If you can't, then extremely difficult.

From the post, I'm not sure you really want answers to the questions you actually asked ("how hard would it be"). Perhaps you are more interested in the answer to "will somebody here make this for me", how much do you think it should cost to get a custom item like I want made" or something along those lines.