Hello all.
I.ve had my mavic.pro 1 since july, and i have flown with it more than 40 times, dealing with several glitches.
But today, was a great day to fly lol... Happenned too many.
(to say all from the start, in august, i had a small crash, IT touched a tent and landed on the tent upside down-no speed, landed really soft, not a single scratch on the drone whatsoever, had no problems since).
But today...
1) First of all, since 4 flights ago, i got a gimbal.overload error at startup, right until it finishes the calibration. Is it normal? Or am i paranoic? After the calibration is done, the gimbal performs ok, no problems whatsoever. If i start a manual calibration, the gimbal does it ok, it does not get stuck as i read on forums. Could this be a software problem?
Before tent-touching (i cannot name it a crash ), i had several gimbal freakouts, as i.ve read here, could be because of the 64gb sd card
-So, ignoring gimbal overload startup message, i proceed on flying. I.ve had used for the first time a gimbal protection bought on amazon. I put the camera on portrait mode, and there it was: all of the sudden the camera started spinning mid air like crqzy. I looked at the phone and i thought that the drone was spinning and it was going to fall. But no, it was the gimbal. I took some photos on the way home and all.my photos were upside down, the camera could not seem to figure out what portrait mode means.
3) since i bought the drone, i have compass errors mid flight!!!, that last under a second untill i move the drone a bit.But today i had like 3 compass errors in one flight, and the 2nd one appeared for about 2 minutes, and i really panicked.
I have the latest firmware etc.
So, my questions are: gimbal.overload: is itnormal at startup? Should i get worried? Is it a software bug? What about that compass error mid flight? Cand it cause a crash?
Ty!!!!
I.ve had my mavic.pro 1 since july, and i have flown with it more than 40 times, dealing with several glitches.
But today, was a great day to fly lol... Happenned too many.
(to say all from the start, in august, i had a small crash, IT touched a tent and landed on the tent upside down-no speed, landed really soft, not a single scratch on the drone whatsoever, had no problems since).
But today...
1) First of all, since 4 flights ago, i got a gimbal.overload error at startup, right until it finishes the calibration. Is it normal? Or am i paranoic? After the calibration is done, the gimbal performs ok, no problems whatsoever. If i start a manual calibration, the gimbal does it ok, it does not get stuck as i read on forums. Could this be a software problem?
Before tent-touching (i cannot name it a crash ), i had several gimbal freakouts, as i.ve read here, could be because of the 64gb sd card
-So, ignoring gimbal overload startup message, i proceed on flying. I.ve had used for the first time a gimbal protection bought on amazon. I put the camera on portrait mode, and there it was: all of the sudden the camera started spinning mid air like crqzy. I looked at the phone and i thought that the drone was spinning and it was going to fall. But no, it was the gimbal. I took some photos on the way home and all.my photos were upside down, the camera could not seem to figure out what portrait mode means.
3) since i bought the drone, i have compass errors mid flight!!!, that last under a second untill i move the drone a bit.But today i had like 3 compass errors in one flight, and the 2nd one appeared for about 2 minutes, and i really panicked.
I have the latest firmware etc.
So, my questions are: gimbal.overload: is itnormal at startup? Should i get worried? Is it a software bug? What about that compass error mid flight? Cand it cause a crash?
Ty!!!!