Firmware v01.03.0500

Cerberus · Mar 2, 2017

Updated mine a couple of minutes ago.. was at work and didn't want to waste time downloading DJI assistant 2 on my lappy..

Did notice my video settings were all resetted so I did a IMU and compass calibration again just to be sure..
Can't test fly it (at work obviously) but will do it tonight most likely..

So far, everything works out fine.. Test fired up the props and all looks good... CAmera looks good... everythings a go for tonight I think..

rmadrid20 · Mar 2, 2017

iOS Go 4 has been updated

dangerm0us · Mar 2, 2017

IOS App Store v4.0.5 Change Log:

- Added feature that precisely record takeoff point
- Increase max flight speed to 15 m/s when using ActiveTrack
- Added support for simultaneous control of aircraft by Primary and Secondary Remote Controllers

kc9sdo · Mar 2, 2017

Version 4.0.5 of the DJI GO 4 app just showed up in my iPhone App Store updates list. Just downloaded and checking it out now.

Egika · Mar 2, 2017

rmadrid20 said:
iOS Go 4 has been updated

Check out separate thread:
DJI GO 4.0.5 for iOS

Marc Hufnagel · Mar 2, 2017

dangerm0us said:
IOS App Store v4.0.5 Change Log:

- Added feature that precisely record takeoff point
- Increase max flight speed to 15 m/s when using ActiveTrack
- Added support for simultaneous control of aircraft by Primary and Secondary Remote Controllers

quite a bit more than that ^^^

dangerm0us · Mar 2, 2017

Marc Hufnagel said:
quite a bit more than that ^^^

That was just the Mavic specific stuff.

dangerm0us · Mar 2, 2017

Firmware update completed. Approx 15 mins. No issues with update. Have not tested the bird yet....

djl61 · Mar 2, 2017

Updated to day, took about 15-20 min. I will fly in the morning to see

dewster · Mar 2, 2017

My RTH height was reset after the update along with obstacle avoidance settings. The No Fly Zone that I'm in indicates "Nuclear Power Zone". There's no nuclear power plants here. Lol

I'll have to wait to fly it though.

Sent from my iPhone using MavicPilots

gusri.candra · Mar 3, 2017

Just update. The downloading of restriction zone was really annoying.

Craig540 · Mar 3, 2017

I updated with no problems, Will test fly tomorrow. I did notice inside that it no longer goes back and forth from ATI then GPS, just stays in ATI mode. I think I might try indoors again.

Sportflyer · Mar 3, 2017

So the mavic can now fly with two remotes, with two people being able to control it like the inspire?
Also I am wonder how much more precise the RTH got?

Vasco · Mar 3, 2017

To update or not to update.....???? This is the question! I have 0200 version till now with no problems at all. I am wondering should i take the risk?

bakerboy · Mar 3, 2017

Vasco said:
To update or not to update.....???? This is the question! I have 0200 version till now with no problems at all. I am wondering should i take the risk?

I'm in the same boat, going to give it a crack though

Vasco · Mar 3, 2017

And as far as i can see you can not downgrade to 0200 if something not working with new one....

larkin · Mar 3, 2017

Vasco said:
And as far as i can see you can not downgrade to 0200 if something not working with new one....

You can downgrade to any previous firmware with dji assistant

dewster · Mar 3, 2017

Sportflyer said:
So the mavic can now fly with two remotes, with two people being able to control it like the inspire?
Also I am wonder how much more precise the RTH got?

I thought the precision of RTH was spot on. How much better can it get?