some guy doing an FCC hack permanent for RC pro Controller
- Thread starter Scoobychief
- Start date
Hi guys,
is anyone missing Remote ID after the patch? I have RC Pro and as soon as I apply the mod, FCC works, however Remote ID (DroneID) field in the DJI Fly app disappears, no matter what version app or RC Pro FW (currently 3.02.0500).
The "droneid on" command (About section, Name) does not work at all. Nor does work "force_fcc off" or "CC IT" to turn off FCC.
I need Remote ID in Europe to avoid fines and possible troubles. Anyone in similar situation?
Thanks!
is anyone missing Remote ID after the patch? I have RC Pro and as soon as I apply the mod, FCC works, however Remote ID (DroneID) field in the DJI Fly app disappears, no matter what version app or RC Pro FW (currently 3.02.0500).
The "droneid on" command (About section, Name) does not work at all. Nor does work "force_fcc off" or "CC IT" to turn off FCC.
I need Remote ID in Europe to avoid fines and possible troubles. Anyone in similar situation?
Thanks!
Today i updated my 3 classic to latest FW, the DJI RC (1) had no updates.
I then checked FCC status and was OK, tried CC IT and CC US commands to disable enable FCC, they worked, but then noticed the droneid section was missing in the DJI FLY. I powered off M3C and RC and then the droneid section reappeared at next boot with fcc active.
lschabert
Member
As there is a newer Dji rc firmware (01.03.1600) any one tested it already if it works with djifcc?
TheMavic
Well-Known Member
- Joined
- Oct 16, 2017
- Messages
- 66
- Reactions
- 22
Telegram dji club and seller you may need sub to english translate like I did to communicate correctly
Attachments
Last edited:
RC with the latest firmware installed. Never been patched. Is there a way to install this fcc hack or isn't possible?
Thank you
Thank you
lschabert
Member
Yes for the DJI RC Pro, however for the regular DJI RC model no.
No this cannot be used with firmware newer than V01.03.1200 for the DJI RC (RM330).
You might be able to use Drone Tweaks FCC service. However that's a temporary patch that you have to enable every boot of the RC. 1 year of service for around $30.
lschabert
Member
I contacted them, but that was for the RC Pro, not the regular RC. Unfortunately the only thing we can do at the time, is to buy a new DJI RC. Still in the package and not updated, And then do the FCC patch.
I was able to buy one on AliExpress for around $175.
I know it's a crappy solution.
I'm also wondering if anyone has already upgraded fw to 01.03.1600 to already patched RC with FCC, applied FCC patch again - still works?
Not an answer to your question , just my insight :
I have updated to 1400 myself but wouldnt update to 1600 just yet , since on the "official djifcc" website they still recommend updating to only 1200 and not beyond . I think even 1400 is pushing it at this point .
Firmware .0800 for mini 3 pro has brought very bad signal range for many and there is no way to downgrade to an earlier version . Same could happen to the controller by going to 1600 , it seems they are changing many things and are rolling updates out in stages . Better safe than sorry and not update too soon .
Especially since the dji changelogs are always super vague .
I could not get it to work with the latest firmware v03.02.0800
v03.02.0700 is fine, I believe.
lschabert
Member
Ciao, al momento non è possibile per DJI RC rm330 sulla versione 01.03.1300 e successive. Dovremo aspettare e vedere se rilasciano un hack per le nuove versioni.
Similar threads
DJI Drone Deals
New Threads
-
-
-
-
Cannot connect with Litchi
- Started by AntoineD
- Replies: 0
-
Disadvantage of using "explore" mode on Mavic 3 Pro?
- Started by wrybread
- Replies: 1
Forum statistics
