gimbal

So flew my mavic about 7 times Had it in my back pack and i think gimbel got knocked as i didbt hsve protection on it. I get gimbel overload. Wont calibrate passed 31% And it makes this knocking noise see video Video Im yet to replace the ribbon cable

Hi, Hope for some advice.... When I try to capture shots travelling diagonally (up & left/right). The horizon is really out of level. I'm flying a Mavic 2 pro and it is new, never crashed etc. I've calibrated the gimbal but doesn't seem to make any difference. I've added an example video below...

I recently bought a Mavic off of eBay but I’m not sure if something’s wrong with the gimbal. It seems pretty loose when it’s off to the point where if I hold it side ways it turns and hits the side. Not sure if this is normal or not

Hello everybody! New drone operator here. Bought a refurbished unit from the DJI website. I got a little arrogant and crashed my drone. Pretty big impact. Destroyed the gimbal. I ordered a replacement gimbal off of ebay and installed it myself. When I start up the drone, I am able to connect...

I recently found that all footage I took the last two weeks is extremely shaky. The issue seems to be much worse on anything that is close to the drone such as the trees to the bottom right side, but anything far away seems to be fine. I think it almost looks like a stabilization issue. Is...

Hi I recently noticed a bulge in the o-ring that seals the camera lens when a lens protector or filter is put on. I figured that such a trivial part would be available for 10c form DJI but no.............the drone has to be sent away and for whole gimbal to be replaced. I tried a private repair...

Hi All! New to the group and unfortunately I come bearing bad news. I was pushing my luck with my dji zoom and now I have a warning saying “gimball motor load to large” and “gimball obstructed”. The gimball almost rotates a full 360 but then stops on its final stages before being centre again...

I have a Mavic 2 Pro. I am still a beginner to fly drones. One day I turned on the Drone in my hand and put it on the floor, so I took the remote control to turn it on too. That's when I looked that I hadn't removed the Gimbal cover. Whenever I turn on the Drone, the gimbal does a calibration. I...

I have inherited a Mavic Pro from a friend who bought a new mavic after his got stepped on. Everything works except the gimbal. (Including the camera). I have replaced the ribbon cable to no avail. If you were in my position would you rather buy the gimbal with camera and no vibration plate...

I had some issues with keeping direction. I thought it was wind (it may still be), but then I started examining the gimbal. And I found that when my Mavic is positioned on a straight line (line right in the centre, between feet and the feet aligned to another line positioned at right angle to...

So a few weeks ago, my Mavic Air started doing this weird thing. When it’s up in the air, and I try to adjust the pitch of the gimbal, the gimbal moves, but the drone also moves sideways, in which ever direction the dial is turned. I tried recalibrating a few things, but nothing worked. Any...

Hey peeps, I had a Mavic 2 pro, everything was fine until the day came. My Mavic 2 pro fell into a freshwater lake in Arkansas. I sent it to DJI but they wouldn't even touch a water damaged drone. So i didnt know what to do for the last 6 months and just kept it stored...

So the title says it. I broke the clip off (where the arrow is pointing). Is there anyway I can stabilize it? (Duct tape etc.)

Everything else on the mavic works fine. The camera stays facing down when off though. I can move it in any direction manually but will center itself facing down. When I turn it on it positions itself normally and works normal. Only when I fly and move it around the camera drifts and faces down...

Hi, my ribbon cable flex was damaged (without any crash) so i ordered a new one and changed it with various youtube videos. The classic "gimbal motor overload" message is not poping out now, but the camera is facing down looking at the zenith (-90° i guess) *the remote control is calibrated *i...

Gents, My drone finally crashed at the hands of my friend (doh!) Did a little bit of research and i think if i buy the 2 below items i might be able to repair it. Attached/below are pictures of what broke and what i plan to buy and fix it with. I think i need a new camera arm/body to fix...

Hi Mavic Proers! I had an accident with my bird and the gimbal was damaged. I bought a gimbal and replaced it but got a knocking sound so I read some forums and though it should be the gimbal ribbon. I purchased a new ribbon and replaced it but I still have the knocking but I guess in a...

Problem: Gimbal tilts up by itself randomly even when sitting on my desk. Other than that it works as expected most of the time. It's just a bummer to have the gimbal tilt up in the middle of recording a shot that you then have to do over again hoping there will be no tilt. Was unit in a crash...

Not too long ago, I crashed my mavic pro. It was about 14 feet up when it got hit by a football and fell to the ground. The battery came out and the propellers were cracked. I thought that was the end of the issues though. Turns out i broke the ribbon cable for the gimbal. I replaced it and the...

I purchased a second-hand Mavic 1 pro recently with the owner stating that it needed a gimbal ribbon replacement. It was a good price so I figured I could try and fix it as a project. I have an issue after replacing the gimbal ribbon and video cable. I still get the 0x800000 error but the...