gimbal

Problem: Gimbal tilts up by itself randomly even when sitting on my desk. Other than that it works as expected most of the time. It's just a bummer to have the gimbal tilt up in the middle of recording a shot that you then have to do over again hoping there will be no tilt. Was unit in a crash...

Not too long ago, I crashed my mavic pro. It was about 14 feet up when it got hit by a football and fell to the ground. The battery came out and the propellers were cracked. I thought that was the end of the issues though. Turns out i broke the ribbon cable for the gimbal. I replaced it and the...

I purchased a second-hand Mavic 1 pro recently with the owner stating that it needed a gimbal ribbon replacement. It was a good price so I figured I could try and fix it as a project. I have an issue after replacing the gimbal ribbon and video cable. I still get the 0x800000 error but the...

Hi, So I accidentally crashed the drone. Directly after the camera feed went black and the gimbal did not respond. I opened the gimbal it up and the ribbon was broken. Replaced that but now it says in the go 4 app, Gimbal status n/a. No video, no gimbal reaction when startup or when trying...

Hi there, I constantly get Gimbal Overload errors after start up (Never had a crash or anything similar). The funny thing is that the gimbal works normally when booting the Mavic keeping it sideways. In that case it works for a couple of minutes, after that it starts to go crazy and twists and...

Hi I was just wondering if anyone else has had any issues with the waypoints feature on the Mavic, I set my way points to follow a specific route and once I launch and upload to the aircraft it starts to record and folllows the waypoints fine but the camera is way off either to the left or the...

Hi guys, Sorry if this has been talked about before. I crashed my drone mavic Air and saw the video transmission cable was broken. Got a new on and video is working fine. My issue is that the gimbal now only moves slightly up and down when turning the Mavic on. I have done an auto calibration...

Problem? Gimble Wobbling a lot - before and after take flight Was unit in a crash? No What have you tried so far? See if there is any problem in the gimbal itself, the fitting, and it seems ok, and i calibrated the gimbal on app What device are you using? iPhone 6 What firmware are you...

So I went to fly my new MA, I think it would have been the fourth time to take her out. So far all of my flights have been uneventful, no crashes, no hard landings nothing that would cause problems. I got to my practice spot eager to try out some settings. I slowed down the stick response speed...

Hey there. So in December while filming in a city between buildings my Mavic Pro disconnected from the controller and hit a lamp post. Today I finally got around to try flying it. In spite of all the plastics being broken it flies fine. However the gimbal and camera are not working. After I turn...

Sometimes when stopping or letting off the sticks suddenly at full speed the camera will force itself down or shift down from the stop, causing me to have to move the camera to regular position using the remote. Just happened the other day when stopping. I don’t typically stop suddenly, but let...

Is this rust on the gimbal? If so is there any way to clean it? I just replace it, i was getting a gimbal overload error (no crash).

I'm using GO 4 v4.3.4(689-GooglePlay). Under Settings, I don't have a Gimbal icon between the Aircraft Battery icon and the three dots for general settings. I have a Mavic 2 Zoom. Can you tell me what I'm missing? Using Android and it shows no update.

Hi all, I remember reading in a post somewhere that to solve the camera gimbal error status/compatibility issue when changing to a new gimbal the replacement gimbal must have the same ID prefix stamped on the gimbal circuit board. Can anyone point me to the post or can confirm this is true? I...

Silly me trying to land on reflective surface “top of me car” the drone could not find the car, so I try to assist in landing, it landed on the edge of the top. Then it fall . Some scratches on the right leg, and I think it is broken but still holding. Some scratches on the camera body. On...

Hi everyone. The gimbal on my MA is sticky on the roll - it gets a bit stuck off axis, not good for the shots i want. There is no care refresh package available in my region, the authorised repair center has sent the drone logs in, and DJI has advised that they want the drone sent to them for...

Hi everyone, I had a minor crash with my mavic pro two weeks ago. I was getting the errors: 1.Gimbal motor overloaded. Check weather gimbal clamp is removed. 2. Gimbal is restarting. Check that gimbal rotates smoothly if restart fails again. Everything looked fine until I saw one of the LVDS...

This is a mix between a gimbal, a mavic pro, and my custom race platform. I'm pushing the envelop with what I think is palatable; this stuff makes a lot of people sick :) I'm getting better though... Music: Take it Easy by Jetta (matstubs remix) Please feel free to comment!

I was having gimbal motor error after landing a hill with stones. But the gimbal and video was ok. Just cannot calibrate the gimbal and it was knocking. Anyway i tried to replace the ribbon and BOOM. No video now and no movement of gimbal. Then i changed the silver cable (video transmittin) but...

Today, my camera seems to have glitched mid-air. I was physically within 30 yards of my unit though as the flight wasn't affected during this erratic fluttering gimbal for a few seconds. Any thoughts? Mavic pro